JetCon 1301 / 1301-48V Specifications

Overview Specifications Ordering Information Datasheet Power Plant Automation

Industrial Fast Ethernet to Fiber Media Converter  One 10/100 TX port to One 100FX port media converter Dual Forwarding modes- Switching and Pure converter Supports Auto MDI/MDI-X, Auto Negotiation Supports Multi-mode 2KM, Single-mode 30KM Auto Link Loss Forwarding for fault detection Extreme Low Data Forwarding Latency- 1.6 x 10-6 Sec Wide range of AC18-27V/DC18-32V and DC36-60 (JetCon 1301-48V) power inputs with DC polarity protection Aluminum case with IP-31 grade protection Supports 1.5KV Hi-PoT isolation protection Supports single fiber transmission – WDM -10~70°C operating temperature for hazardous environment application (-40~80°C wide operating temperature available by request, please contact Korenix for lead time)

Technology
Standard	IEEE802.3 10Base-T,IEEE802.3u 100Base-TX IEEE802.3u 100Base-FX,IEEE802.3x flow control and back-pressure
Packet transfer mode	Support Switch mode and Pure Converter mode. This feature is select by DIP-switch. The Switch mode will begin to forward the received data only after it received the frame completely, the forwarding latency depends on the packet length and the packet length support 64 to 1600Bytes. The pure converter operating algorithm is different with switch mode; it will direct transfer Ethernet signal without any frame checking
Link Loss Forwarding Technology	Enabled/Disabled by DIP-Switch 1
Hi-pot Testing	Passed AC1.5KV Hi-pot tesing on port-port, power-case and port-power
Interface
Number of Ports	1 x 10/100 Base-TX with Auto MDI/ MDI-X, Auto-Negotiation functions 1 x 100Base-FX
Connectors	10/100 Base-TX: RJ-45 100Base-FX: Duplex SC for multi-mode or single-mode fiber Power: 2-Pin Terminal Block
Cables	RJ-45 connector: supports CAT-3, CAT-4, CAT-5 unshielded twisted pair or shielded twisted pair cable. The link distance is maximum 100 meters SC connector: supports multi-mode or single-mode optical fiber Multi-mode fiber: 50/125um or 62.5/125um, max. distance 2KM Single-mode fiber: 8/125um, 9/125um or 10/125 um, max distance 30KM
Fiber Transceiver	JetCon1301-m, Multi-mode: 2KM (Max.) Wave-length: 1310nm Min TX Power:-19dBm Max TX Power:-14dBm Max RX Sensitivity:-30dBm Link budget:11dBm JetCon1301-s, Single-mode: 30KM (Max.) Wave-length:1310nm Max TX Power:-8dBm Min TX Power:-15dBm Max RX Sensitivity:-34dBm Link budget: 19dBm JetCon1301-s(WDM-A), Single-mode: 30KM (Max.) Wave-length: TX 1310nm, RX 1550nm Max TX Power:-3dBm Min TX Power:-9dBm Max RX Sensitivity:-31dBm Link budget: 22dBm JetCon1301-s(WDM-B), Single-mode: 30KM (Max.) Wave-length: TX 1550nm, RX 1310nm Max TX Power:-3dBm Min TX Power:-9dBm Max RX Sensitivity:-31dBm Link budget: 22dBm JetCon1301-m(48V), Multi-mode: 2KM (Max.) Wave-length: 1310nm Min TX Power:-19dBm Max TX Power:-14dBm Max RX Sensitivity:-30dBm Link budget:11dBm JetCon1301-s(48V), Single-mode: 30KM (Max.) Wave-length:1310nm Max TX Power:-8dBm Min TX Power:-15dBm Max RX Sensitivity:-34dBm Link budget: 19dBm
Configuration DIP Switch	DIP 1: Link loose forwarding Enable /Disable. DIP 2: RJ-45 Auto-Negotiation/Forced 100Mbps Full Duplex DIP 3: Fiber Full Duplex/Half Duplex DIP 4: Switch/Pure Converter mode
Diagnostic LED	System: Power (Green) RJ-45 port: Link (Green ON)/Activity (Green Blinking) Fiber port: Link(Green ON)/Activity(Green Blinking)
Power Requirements
System Power	2 pins terminal block for power input with auto polarity reverse. JetCon1301: DC 24V (18~32V) /AC 18~27V, 47~63Hz JetCon1301-48V: DC 48V (36~60V)
Power Consumption	JetCon1301: 3.5 Watts @ DC 24V(Maximum) JetCon1301-48V: 4 Watts@ DC 48V(Maximum)
Mechanical
Installation	DIN-Rail mount
Case	Aluminum metal case with IP31 grade case protection for drop-waterproof and dustproof
Dimensions	70mm(H) x 30mm (W) x 89mm (D) ( with DIN rail clip) 70mm(H) x 30mm (W) x 80mm (D) ( without DIN rail clip)
Weight	374g with package 292g without package
Environmental
Operating Temperature	-10 to 70°C (JetCon 1301/1301-48V -40~80OC)
Operating Humidity	0% to 95% (Non-condensing)
Storage Temperature	-40 to 80°C
Storage Humidity	0%~ 95% (Non-condensing)
Regulatory Approvals
Hi-Pot	AC1.5KV on port to port and port to power
EMI	FCC Class A, CE/EN55022
EMC Immunity Interface	EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11
Safety	CE/EN60950
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
MTBF:	506,819 Hours, MIL-HDBK-217F GB standard
Warranty	5 years