JetPort 5604 Specifications

Overview Specifications Ordering Information Datasheet	Industrial 4-port Redundant Serial Device Server 4-ports RS-232/422/485 to redundant Ethernet RTTD, Redundant to the Device function Dual Ethernet ports, network auto-recovery in Less Than 200ms Four Digital Inputs and Two Digital Outputs Redundant Power Inputs by 12-48VDC Terminal Block and DC Jack Independent serial services, Virtual COM, TCP Server/Client/Tunnel and UDP Connections JetPort Commander, Easy-to-use Windows Utility with smart setup Wizards Secured Management by HTTPS and SSH Event Notification by Syslog, Email, SNMP trap and Digital Output Vertical mounting by DIN Rail, Wall mount/Desk-top
Coal Mine Monitoring System
Gas Distribution Station

Network Interface
Ethernet	2* 10/100BaseTX, Redundant Dual Ethernet
Connector	RJ-45, Auto MDI/MDI-X
Feature	Auto Recovery in less than 200ms
Protection	Built-in 1.5 KV magnetic isolation protection
Protocols	IP, TCP, UDP, ICMP, DHCP, BootP, ARP/RARP, SNMP, HTTPS, SSH, SNTP, SMTP
Serial Communication
Number of Ports	4
Interface	RS-232, RS422, 2/4-wire RS485
Connectors	Male DB9
Baud Rates	110 bps to 460.8 Kbps
Data Bits	5, 6, 7, 8
Parity	odd, even, none
Stop Bits	1, 1.5, 2
RS-232	TxD, RxD, RTS, CTS, DTR, DSR, GND, DCD
RS-422	Tx+,Tx-, Rx+, Rx-,GND
RS-485 (4-wire)	Tx+,Tx-, Rx+, Rx-,GND
RS-485 (2-wire)	Data+, Data-,GND
Flow Control	XON/XOFF, RTS/CTS, DTR/DSR
Serial Line Protection:	15KV ESD
Long Distance Termination	2*pin 120ohm DIP switches
Digital Input/Output
Number of DI:	4
Power Input voltage:	5V/TTL Logic 0: 0.8V max (0-0.8V) Logic 1: 2.0V min (2-5V)
Number of DO:	2
Power Output voltage	5V/TTL Logic 0: 0.8V max (0-0.8V) Logic 1: 2.0V min (2-5V)
Features
LED	Power 1/Power 2: Startup(Red); Ready(Green) Ethernet port: Left:100M Link (Green On) / Activity(Green Blinking) Right:10M Link (Orange On) /Activity(Orange Blinking) Serial 1/2/3/4:TX only(Green), RX only(Red), Both RX/TX(Orange)
Configuration	Windows Utility-JetPort Commander, HTTP, Telnet
Serial Service	Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP
Reset	Software reload default, Hardware reset button
Beeper	Embedded beeper for positioning
RTTD	Redundant to the Device, Auto-recover in less than 200ms
SNTP	For time management
Access IP Table	16 IP addresses to prevent illegal users
Monitor	Devices¡¦ status, VCOM status
SNMP	RFC1213 MIB II, RFC1317 RS232_like and SNMP Trap
E-Mail Alert	Automatic e-mail warning by pre-defined events
System Log	Trap to Syslog server or local display
System Events	Cold/Warm Start, Login Failed, IP and Password Changed, Access IP Blocked, DI/DO changed, Serial Port DCD/RI/DSR/CTS changed, Serial Port connected/disconnected.
Windows Utility
JetPort Commander	Device Discovery, Auto IP, Network Setting, Device and Serial Port Setting and monitoring, Notification setting, Firmware Upgrade, Configuration Backup and Restore, Group Configuration Wizards
Serial Service Mode	Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP
Advanced Serial Setting	TCP Alive Check Timeout, Inactivity Idle Timeout, Performance mode, Delimiter, Force TX Timeout for Data Packing and Force TX interval time
Group Configuration Wizard	JetPort Commander: Group IP Wizard, Group firmware upgrade, Group Backup/Restore, VCOM and TCP Tunnel Setup Wizard
Power Requirements
System Power	PWR1: 12~48VDC Terminal Block PWR2: 12~48VDC Power Jack with Power Adapter
Power Line protection	1 KV Burst (EFT), EN61000-4-4 0.5 KV Surge, EN61000-4-5
Mechanical
Dimensions	145mm(W)x46.5mm(H)x120mm(D)
Regulatory Approvals	FCC Class A, CE Class A , UL, RoHS
Environmental
Operating Temperature	-10 to 70°C
Operating Humidity	5% to 95% (Non-condensing)
Storage Temperature	-40 to 85°C
Warranty	5 years